How to Calculate Mabati Sheets Needed for Your Roof
Standing in a mabati shop with only a rough sketch of your roof is how people end up buying too many sheets or too few. A tape measure, the sheet's cover width and a small allowance for cutting give you a count you can trust. Once you have your number, you can price it against real sheets.
Get the best roofing sheets prices in Kenya

Every homeowner or small contractor in Kenya who has stood in a mabati shop with a rough sketch knows the nervous feeling of not being sure how many sheets to buy. Learning to calculate mabati sheets needed for roof work properly takes only a tape measure, a notebook and about an hour of careful thinking. This post walks you through the method one step at a time, using the same logic that experienced fundis use on site. It is a companion to our Mabati in Kenya Guide, so if you want the bigger picture on profiles, gauges and finishes, that is the place to start. Here we focus on one question: how many sheets does your roof really need? By the end you will be able to take your own measurements, apply the overlaps correctly, add a sensible allowance and walk into the shop with a figure you can defend.
Why Getting the Sheet Count Right Matters
Over-ordering feels safe, but it quietly eats your budget. A pile of twenty extra G28 sheets is real money sitting in your compound instead of paying for timber, labour or cement. Leftover sheets are also awkward to deal with, because suppliers do not always accept returns on cut or scratched stock, and a sheet that has sat in the rain for a month may no longer look new. Even if you can sell them on, you will rarely recover what you paid. Spending that money on the build itself is nearly always the better choice.
Under-ordering causes a different set of problems, and they tend to show up at the worst moment. The roofing gang is on site, the rafters are ready, and you discover you are six sheets short. A second delivery means another transport charge and a day or more of idle labour. It can also mean a different production batch, and mabati from separate batches can vary slightly in colour, especially in shades like charcoal grey or tile red. That mismatch becomes visible on a sunny day, and it is very hard to fix once the roof is fixed down.
Both homeowners and small contractors benefit from a clear counting method. The homeowner gets a budget they can trust and fewer arguments with the builder. The contractor gets a quotation that holds up, which protects both margin and reputation. A written method also makes it easy to explain your figures to a client or to the supplier, who can then check them quickly. The steps below are simple enough to do with a pen and paper, and they work whether the roof is a small kiosk or a four-bedroom house.
Measure the Roof Length and Width Accurately
Start by measuring each roof slope separately, because the sheet count is worked out slope by slope. For a simple gable roof you have two slopes, and for a hipped roof you have four, each with its own shape. The measurement that matters is the true slope length, taken from the eave down at the bottom to the ridge at the top, along the surface the sheets will cover. It is not the horizontal distance you would read off a floor plan. A roof with a 20 degree pitch is noticeably longer along the slope than it looks from below, so a plan measurement will always leave you short.
Next, add the overhang. Mabati should extend past the fascia at the eaves so that water drops into the gutter or clear of the wall, and most builders allow roughly 150 to 300 millimetres for this. The gable ends usually need a small overhang as well, so the sheets protect the barge board and the top of the wall. Add these figures to your raw measurements before you do any sums. For example, if the rafter slope measures 3.9 metres and you want a 0.3 metre eave overhang, your sheet run is 4.2 metres. If the building is 8 metres long and you want 0.3 metres of overhang at each gable, your roof width along the ridge is 8.6 metres.
Measure at more than one point, because few roofs in real life are perfectly square. Take the slope length near each end and in the middle, and do the same for the width at the eave and near the ridge. Walls built by hand can be a few centimetres out, and rafters can sit unevenly. Always use the longest reading, since a sheet that is too short cannot be stretched, while a sheet that is slightly long can be trimmed. If two readings differ by more than a few centimetres, it is worth telling your fundi, because it may point to a framing problem that should be corrected before the roofing starts.
Account for Sheet Overlap and Cover Width
The width printed on a sheet is not the width it covers once installed. Corrugated and box profile sheets overlap their neighbours at the side, so each sheet adds only its effective cover width to the roof. A sheet that measures about 0.86 metres across may cover only around 0.80 metres once the side lap is taken into account, and the exact figure depends on the profile and the manufacturer. Tile style sheets behave the same way, with their own cover width. Ask the supplier for the effective cover width of the exact profile and gauge you are buying, and use that number instead of the full width.
Overlap also applies along the length of the roof. If your slope is longer than a single sheet, the sheets in the upper row must lap over the lower row, and that end lap is lost length. Many roofs use an end lap of around 150 to 200 millimetres, though your supplier or the manufacturer's guidance should give the correct figure for your profile. Steeper pitches shed water quickly and can manage with the lower end of that range. Low pitches and windy or exposed sites, such as hilltops, open plots and areas near the coast, call for a slightly larger lap so wind-driven rain cannot be pushed underneath. When in doubt, choose the larger overlap, because the cost of one extra row of material is small compared with the cost of a leaking roof.
Calculate Mabati Sheets Needed for Roof, Step by Step
Begin with the number of sheets across each slope. Divide the roof width by the effective cover width of the sheet. Using our example, 8.6 metres divided by 0.8 metres gives 10.75, and because you cannot buy three quarters of a sheet, you round up to 11 sheets across. Always round up at this stage. The last sheet can be trimmed at the gable if it overshoots, which is far better than leaving a gap.
Now work out how many sheets are needed up the slope. If you can order sheets cut to the full 4.2 metre run, you need only one sheet in each column, so one row of sheets covers the slope with no end lap at all. If you are using standard 3 metre sheets instead, subtract the end lap first. With a 150 millimetre lap, each sheet contributes 2.85 metres of usable length, and 4.2 divided by 2.85 is about 1.47, so you round up to two rows. Fewer joins means fewer places for water to enter, so the single long sheet is often the better option when it can be delivered and handled safely.
Finally, multiply and add up. Eleven sheets across multiplied by one row gives 11 sheets for one slope, so a two-slope gable roof needs 22 sheets before any allowance. With 3 metre sheets, 11 across multiplied by two rows gives 22 per slope, so 44 for the whole roof. For a hipped roof, repeat the process for each slope, treating the triangular hip slopes as full rectangles at first, and then add everything together. Write each slope's calculation on its own line so you can check the working later. Count the ridge caps, roll caps and fasteners separately, using the ridge length and the number of sheets and purlins as your guide.
Add a Safe Allowance for Waste and Cutting
No roof is perfectly rectangular, so you will need extra sheets for cuts. Hips, valleys and gable ends all involve angled cuts, and each cut produces an offcut that often cannot be reused. A common allowance is around 5 to 10 percent on top of your calculated total. A plain gable roof with square corners sits near the 5 percent end, while a roof with several hips, valleys or dormers should lean toward 10 percent. On our 22 sheet example, that means buying 23 or 24 sheets, and on the 44 sheet version it means 46 to 48.
Sheet length is the other lever you can use to keep waste low. Mabati is made in a range of standard lengths, and many suppliers will cut to measure, so choosing lengths that match your slope reduces end laps and the number of joints. A roof that can be covered by a single 4.2 metre sheet in each column uses less material overall than one built from shorter sheets with laps. Longer sheets are heavier and need more careful handling, so be realistic about your crew and access. Talk it through with the supplier, who can tell you which lengths are in stock and what the price difference is.
Think about offcuts before you decide how much extra to buy. The triangular piece cut off at a hip on one side often fits perfectly on the opposite hip, so some of that waste is recoverable if your fundi plans the cutting. Offcuts can also be used on small jobs such as a lean-to over the gas cylinder, a pit latrine or a dog kennel. If you have no use for leftovers, stay near the lower end of the allowance range. If you do have a small side project planned, going slightly higher can make sense, as long as you are doing it deliberately and not out of nerves.
Check Your Count Before You Order
Before you commit, sketch the roof on paper and label every slope. Draw the shape, write the width and slope length along each side, and mark the overhangs you added. Beside each slope, write the number of sheets across, the number of rows and the subtotal. A sketch makes mistakes easy to spot, such as a slope you forgot or a measurement entered twice. It also gives you something to show the supplier, which speeds up the conversation considerably.
Compare your figure with a second measurement taken by someone else, preferably your fundi or a colleague who has not seen your numbers. If both of you arrive at the same count, or within a sheet or two, you can be confident. If the totals differ significantly, find out why before you pay, because one of you has probably misread the tape or missed an overhang. Finally, confirm the gauge, profile and colour with the supplier, whether you have chosen G28 or G30, corrugated, box profile or tile style. Ask that the whole order be supplied from the same batch, so every sheet matches in colour and finish from the first row to the last.
Counting mabati sheets is not guesswork once you break it into small, repeatable steps. You measure each slope along its true length, add the overhangs, and use the longest reading. You then replace the full sheet width with the effective cover width, allow for the end lap, and divide to find the sheets across and the rows up. After multiplying, you add 5 to 10 percent for cuts, check the figure against a sketch and a second measurement, and confirm the specification with your supplier. Do this carefully and you will spend only on the sheets your roof needs, and you will avoid the delays and colour mismatches that come from topping up later. If you would like a second pair of eyes on your numbers, bring your sketch to Smart Builders Africa and our team will help you confirm the profile, gauge and quantity before you order.
Get the best roofing sheets prices in Kenya
Best Mabati Prices →